Captivate audiences and enhance your storytelling abilities with ISD3900 and TM4C1294NCPDT

/*!
 * \file 
 * \brief RecNPlay Click example
 * 
 * # Description
 * This application demonstrates the processof recording a message and playing it back.
 *
 * The demo application is composed of two sections :
 * 
 * ## Application Init 
 * Initializes SPI interface in proper mode and performs all the necessary commands to
 * put the device in proper working mode (chip reset, chip power up, chip erasing, clock configuration).
 * 
 * ## Application Task  
 * Performs the chip configuration for recording message via microphone, then records a message
 * for 8 seconds to specified memory location. After that, it reads the recorded message address with message length and then plays the
 * recorded message. When playback is done it erases the recorded message from memory. Afterwards, it repeats all the operations every 10 seconds.
 * 
 * *note:* 
 * The ISD3900 must be properly configured to work in record mode every time when user wants to record a message.
 * When user wants to play a recorded message, then ISD3900 must be properly configured, but now to work in play mode.
 * 
 * \author MikroE Team
 *
 */
// ------------------------------------------------------------------- INCLUDES

#include "board.h"
#include "log.h"
#include "recnplay.h"

// ------------------------------------------------------------------ VARIABLES

static recnplay_t recnplay;
static log_t logger;
static uint32_t msg_addr;
static uint16_t msg_len;
static uint8_t temp_var;
static uint8_t volume;
static RECNPLAY_RETVAL status_byte;
static uint8_t interr_byte;

static const uint8_t config_play_pwm_spk[ 32 ] = { 0x64, 0x00, 0x44, 0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x26, 0x00, 0x57, 0x01, 0x57, 0x00, 0x00, 0xFF, 0x30, 0x02, 0x00, 0x00, 0x00, 0xFF, 0x00, 0xFF, 0x00, 0x00 };
static const uint8_t config_play_aux_out[ 32 ] = { 0x64, 0x00, 0x48, 0x00, 0x40, 0x80, 0xC1, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x26, 0x00, 0x57, 0x01, 0x57, 0x00, 0x00, 0xFF, 0x30, 0x02, 0xAB, 0x00, 0x00, 0xFF, 0x00, 0xFF, 0x00, 0x00 };
static const uint8_t config_rec_mic[ 32 ]      = { 0xA4, 0x80, 0x02, 0xFF, 0x0D, 0x40, 0x50, 0x48, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x28, 0x00, 0x3E, 0x00, 0xD6, 0x00, 0xFF, 0xFF, 0x11, 0x82, 0x00, 0x00, 0x00, 0xFF, 0x00, 0xFF, 0x00, 0x00 };


// ------------------------------------------------------- ADDITIONAL FUNCTIONS

void wait_cmd_fin ( void )
{
    status_byte = recplay_read_status( &recnplay, &interr_byte );
    while ( ( interr_byte != RECPLAY_INT_CMD_FIN_MASK ) || 
                ( status_byte != ( RECPLAY_STAT_DBUF_RDY_MASK | RECPLAY_STAT_INT_GEN_MASK ) ) )
    {
        status_byte = recplay_read_status( &recnplay, &interr_byte );
    }
    status_byte = recplay_read_interr( &recnplay, &interr_byte );
}

void wait_ready ( void )
{
    status_byte = recplay_read_status( &recnplay, &interr_byte );
    while ( status_byte != RECPLAY_STAT_DBUF_RDY_MASK )
    {
        status_byte = recplay_read_status( &recnplay, &interr_byte );
    }
    status_byte = recplay_read_interr( &recnplay, &interr_byte );
}

void wait_power_up ( void )
{
    status_byte = recplay_read_status( &recnplay, &interr_byte );
    while ( status_byte == RECPLAY_STAT_PWR_DOWN_MASK )
    {
        status_byte = recplay_read_status( &recnplay, &interr_byte );
    }
    status_byte = recplay_read_interr( &recnplay, &interr_byte );
}

void time_record ( uint32_t seconds_time )
{
    uint8_t cnt;
    for ( cnt = 0; cnt < seconds_time; cnt++ )
    {
        Delay_ms ( 1000 );
        log_printf( &logger, "." );
    }
}

void set_volume ( uint8_t volume_sel )
{
    uint16_t volume_res;

    if ( volume_sel > 100 )
    {
        volume = 0;
        log_printf( &logger, "Volume is: 100%\r\n" );
        return;
    }

    volume_res = 255 * volume_sel;
    volume_res /= 100;
    volume = 255 - volume_res;

    log_printf( &logger, "Volume is: %u%%\r\n", ( uint16_t ) volume_sel );
}

// ------------------------------------------------------ APPLICATION FUNCTIONS

void application_init ( void )
{
    log_cfg_t log_cfg;
    recnplay_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    recnplay_cfg_setup( &cfg );
    RECNPLAY_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    recnplay_init( &recnplay, &cfg );

    log_printf( &logger, "Chip reset...\r\n" );
    recplay_reset( &recnplay );
    log_printf( &logger, "Power up...\r\n" );
    recplay_pwr_up( &recnplay );
    wait_power_up( );
    log_printf( &logger, "Chip Erasing...\r\n" );
    recplay_erase_chip( &recnplay );
    wait_cmd_fin( );
    log_printf( &logger, "Clock Configuration...\r\n" );
    status_byte = recplay_set_clk_cnfg( &recnplay, 0x34 );
    log_printf( &logger, "----------------------------\r\n" );
    volume = 0;
    Delay_ms ( 1000 );
}

void application_task ( void )
{
    uint8_t cnt;
    log_printf( &logger, "Preparing to record a message\r\n" );
    for ( cnt = 0; cnt < 32; cnt++ )
    {
        if ( ( cnt != RECPLAY_CFG0A_REG ) && ( cnt != RECPLAY_CFG1C_REG ) && ( cnt != RECPLAY_CFG1E_REG ) )
        {
            wait_ready( );
            temp_var = config_rec_mic[ cnt ];
            status_byte = recplay_write_cnfg_reg( &recnplay, cnt, &temp_var, 1 );
        }
    }
    wait_ready( );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, "Message recording" );
    status_byte = recplay_record_msg_addr( &recnplay, 0x12000 );
    time_record( 8 );
    status_byte = recplay_stop( &recnplay );
    wait_cmd_fin( );
    log_printf( &logger, "End of recording\r\n" );

    status_byte = recplay_read_msg_addr( &recnplay, &msg_addr, &msg_len );
    log_printf( &logger, "Message Address: 0x%lx\r\n", msg_addr );
    log_printf( &logger, "Message Length: %u\r\n", msg_len );
    Delay_ms ( 1000 );

    log_printf( &logger, "Preparing to play a message\r\n" );
    set_volume( 100 );
    for ( cnt = 0; cnt < 32; cnt++ )
    {
        if ( ( cnt != RECPLAY_CFG0A_REG ) && ( cnt != RECPLAY_CFG1C_REG ) && ( cnt != RECPLAY_CFG1E_REG ) )
        {
            wait_ready( );

            if ( cnt == RECPLAY_CFG03_REG )
            {
                temp_var = volume;
            }
            else
            {
                temp_var = config_play_pwm_spk[ cnt ];
            }
            status_byte = recplay_write_cnfg_reg( &recnplay, cnt, &temp_var, 1 );
        }
    }

    wait_ready( );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );

    log_printf( &logger, "Message is playing...\r\n" );
    status_byte = recplay_play_msg( &recnplay, 0x12000, 0 );
    wait_cmd_fin( );
    log_printf( &logger, "End of playing...\r\n" );


    log_printf( &logger, "Status Byte: 0x%x\r\n", ( uint16_t ) status_byte );
    log_printf( &logger, "Interrupt byte: 0x%x\r\n", ( uint16_t ) interr_byte );
    Delay_ms ( 1000 );

    log_printf( &logger, "Message erasing...\r\n" );
    status_byte = recplay_erase_msg( &recnplay, 0x12000 );
    wait_cmd_fin( );
    log_printf( &logger, "End of erasing\r\n" );

    log_printf( &logger, "----------------------------\r\n" );
    Delay_ms ( 1000 );
}

int main ( void ) 
{
    /* Do not remove this line or clock might not be set correctly. */
    #ifdef PREINIT_SUPPORTED
    preinit();
    #endif
    
    application_init( );
    
    for ( ; ; ) 
    {
        application_task( );
    }

    return 0;
}

// ------------------------------------------------------------------------ END