Create notification systems for various events or alarms with PIC32MZ2048EFH100 and PAM8904

Alerts that demand attention: Next-gen buzzers that redefine signaling

Published Oct 22, 2023

Click board™

BUZZ 3 Click

Dev. board

Flip&Click PIC32MZ

Compiler

NECTO Studio

MCU

PIC32MZ2048EFH100

Step into the future of audio signaling with next-gen buzzers and witness their transformative impact across a wide spectrum of industries and settings

Hardware Overview

How does it work?

Buzz 3 Click is based on the PAM8904, a piezo-sounder driver with an integrated Multi-Mode charge pump boost converter from Diodes Incorporated. The PAM8904 is a switching driver with a multi-mode charge pump for piezo-sounder. Operating at a fixed frequency of 1MHz, the PAM8904 can drive a sounder load of up to 15nF, providing a 9V output with a minimal component footprint. For adjusting the piezoelectric sounder sound volume, the charge pump can operate in 1x, 2x, or 3x mode. It features thermal shutdown, over-current and voltage protection, and under-voltage lock-out and provides a small inrush current, low EMI, and high efficiency. The sounder driver helps to keep current consumption low and battery life long by employing built-in automatic shutdown and wake-up functions. For example, active current consumption is just 300µA in 1x mode, with an

input voltage of 3V, input frequency of 4kHz, and driving a 15nF piezo. In shutdown mode, the quiescent current is less than 1µA. The Charge Pump Mode pins, EN1 and EN2, are used to set the charge pump into mode 1xVDD, 2xVDD, 3xVDD, or they can be used to put the PAM8904 into a forced low-current Shutdown Mode. The device enters the Normal Operation Mode when one or both EN pins are pulled high. Once the PAM8904 senses a valid signal on the DIN pin, the charge pump will start and provide the desired voltage on the VOUT pin, and the output drive lines labeled as VO1 and VO2 will become active after a period of between 270μs and 350μs depending on the selected Mode. If a valid signal on the DIN line disappears, the PAM8904 will detect that disappearance and then wait 42ms to ensure its disappearance. If, even after this period, there is no valid signal on the DIN line, the PAM8904 switches

to low-current Standby Mode. Buzz 3 Click establishes communication with MCU using several GPIO pins routed on the RST, AN, and PWM pins of the mikroBUS™ socket labeled EN1, EN2, and DIN. There is also a jumper setting labeled as INT BUZZ used to choose between single-ended and differential load configurations and between driving either the onboard piezo-sounder or an externally connected piezo-sounder. This Click board™ can operate with either 3.3V or 5V logic voltage levels selected via the VCC SEL jumper. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. Also, this Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used as a reference for further development.

Features overview

Development board

Flip&Click PIC32MZ is a compact development board designed as a complete solution that brings the flexibility of add-on Click boards™ to your favorite microcontroller, making it a perfect starter kit for implementing your ideas. It comes with an onboard 32-bit PIC32MZ microcontroller, the PIC32MZ2048EFH100 from Microchip, four mikroBUS™ sockets for Click board™ connectivity, two USB connectors, LED indicators, buttons, debugger/programmer connectors, and two headers compatible with Arduino-UNO pinout. Thanks to innovative manufacturing technology,

it allows you to build gadgets with unique functionalities and features quickly. Each part of the Flip&Click PIC32MZ development kit contains the components necessary for the most efficient operation of the same board. In addition, there is the possibility of choosing the Flip&Click PIC32MZ programming method, using the chipKIT bootloader (Arduino-style development environment) or our USB HID bootloader using mikroC, mikroBasic, and mikroPascal for PIC32. This kit includes a clean and regulated power supply block through the USB Type-C (USB-C) connector. All communication

methods that mikroBUS™ itself supports are on this board, including the well-established mikroBUS™ socket, user-configurable buttons, and LED indicators. Flip&Click PIC32MZ development kit allows you to create a new application in minutes. Natively supported by Mikroe software tools, it covers many aspects of prototyping thanks to a considerable number of different Click boards™ (over a thousand boards), the number of which is growing every day.

Microcontroller Overview

MCU Card / MCU

Architecture

PIC32

MCU Memory (KB)

2048

Silicon Vendor

Microchip

Pin count

100

RAM (Bytes)

524288

Used MCU Pins

mikroBUS™ mapper

Charge Pump Mode Pin 1

RB11

Charge Pump Mode Pin 2

RE2

RST

SCK

MISO

MOSI

Power Supply

3.3V

Ground

GND

PWM Signal

RC14

PWM

INT

SCL

SDA

Power Supply

Ground

GND

Take a closer look

Click board™ Schematic

Step by step

Project assembly

Flip&Click PIC32MZ front image hardware assembly

Start by selecting your development board and Click board™. Begin with the Flip&Click PIC32MZ as your development board.

GNSS2 Click front image hardware assembly

GNSS2 Click complete accessories setup image hardware assembly

Board mapper by product7 hardware assembly

Flip&Click PIC32MZ MCU step hardware assembly

Necto No Display image step 8 hardware assembly

Debug Image Necto Step hardware assembly

Software Support

Library Description

This library contains API for BUZZ 3 Click driver.

Key functions:

buzz3_pwm_start - This function starts the PWM module output
buzz3_set_gain_operating_mode - The function set gain operating mode of the PAM8904 piezo sounder driver with integrated charge pump boost converter on Buzz 3 Click
buzz3_play_sound - This function plays sound on buzzer

Open Source

Code example

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

/*!
 * @file main.c
 * @brief Buzz3 Click example
 *
 * # Description
 * This example demonstrates the use of Buzz 3 Click boards with PAM8904 for play the Imperial March. 
 * PAM8904 is piezo-sounder driver with an integrated Multi-Mode charge pump boost converter from Diodes Incorporated. 
 *
 * The demo application is composed of two sections :
 *
 * ## Application Init
 * Initializes GPIO, set AN and RST pin as outputs, begins to write a log. 
 * Initialization driver enables - GPIO and configures the appropriate MCU pin for 
 * sound generation, also write log.
 *
 * ## Application Task
 * Plays the Imperial March melody. Also logs an appropriate message on the USB UART.
 *
 * Additional Functions :
 * - void buzz3_melody( void ) - This function plays the Imperial March melody.
 * 
 * @note
 * The minimal PWM Clock frequency required for this example is the frequency of tone C6 - 1047 Hz. 
 * So, in order to run this example and play all tones correctly, the user will need to decrease 
 * the MCU's main clock frequency in MCU Settings for the certain architectures
 * in order to get the required PWM clock frequency.
 *
 * @author Jelena Milosavljevic
 *
 */

#include "board.h"
#include "log.h"
#include "buzz3.h"

#define W 4*Q         // Whole 4/4 - 4 Beats
#define H 2*Q         // Half 2/4 - 2 Beats 
#define Q 250         // Quarter 1/4 - 1 Beat
#define E Q/2         // Eighth 1/8 - 1/2 Beat
#define S Q/4         // Sixteenth 1/16 - 1/4 Beat
                      

static buzz3_t buzz3;
static log_t logger;

void buzz3_melody ( void ) {
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, H );
    Delay_ms ( 1 + H );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F7, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, H );
    Delay_ms ( 1 + H );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab7, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_G7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Gb7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F7, E );
    Delay_ms ( 1 + E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Bb6, E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Eb7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_D7, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Db7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_B6, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, E );
    Delay_ms ( 1 + E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, H );
    Delay_ms ( 1 + H );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab7, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_G7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Gb7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_E7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F7, E );
    Delay_ms ( 1 + E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Bb6, E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Eb7, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_D7, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Db7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_B6, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, E );
    Delay_ms ( 1 + E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E );
    Delay_ms ( 1 + E );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_A6, Q );
    Delay_ms ( 1 + Q );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_F6, E + S );
    Delay_ms ( 1 + E + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_C7, S );
    Delay_ms ( 1 + S );
    buzz3_play_sound(&buzz3, BUZZ3_NOTE_Ab6, H );
    Delay_ms ( 1 + H );
}

void application_init ( void ) 
{
    log_cfg_t log_cfg;          /**< Logger config object. */
    buzz3_cfg_t buzz3_cfg;      /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.

    buzz3_cfg_setup( &buzz3_cfg );
    BUZZ3_MAP_MIKROBUS( buzz3_cfg, MIKROBUS_1 );
    err_t init_flag  = buzz3_init( &buzz3, &buzz3_cfg );
    if ( PWM_ERROR == init_flag ) 
    {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }

    buzz3_default_cfg ( &buzz3 );
    buzz3_set_duty_cycle ( &buzz3, 0.0 );
    log_printf( &logger, "---------------------\r\n" );
    log_printf( &logger, " Set the gain to x1  \r\n" );
    log_printf( &logger, "---------------------\r\n" );
    Delay_ms ( 100 );
    buzz3_pwm_start( &buzz3 );
    buzz3_set_gain_operating_mode( &buzz3, BUZZ3_OP_MODE_GAIN_x1 );

    log_info( &logger, " Application Task " );
}

void application_task ( void ) 
{
    log_printf( &logger, "   Play the music    \r\n" );
    buzz3_melody( );
    log_printf( &logger, "---------------------\r\n" );
    Delay_ms ( 1000 );
}

int main ( void ) 
{
    /* Do not remove this line or clock might not be set correctly. */
    #ifdef PREINIT_SUPPORTED
    preinit();
    #endif
    
    application_init( );
    
    for ( ; ; ) 
    {
        application_task( );
    }

    return 0;
}

// ------------------------------------------------------------------------ END